Sunshine board canopy installation method Sunshine board canopy installation precautions
Sunshine board is a kind of board in PC board. Many families like to install a sun board canopy at home. It can shelter the rain from the family when it is raining. It has a lot of effects. When we choose to install it, many people don't know how to do it because they don't understand it. Today, Xiaobian will take a look at the installation method and installation precautions for the sun awning canopy !
Sunshine board canopy installation method:
1. First check the skeleton, it must be flat, and there must be no welding burrs or burrs. The skeleton must be thoroughly dry and free of volatile solvents.
2. Lay butyl waterproof tape on both sides of the skeleton to form a small sink.
3. Place the sun board on the skeleton, and reserve expansion joints between the board and the board.
4. Press the EPDM bead at the interface between the board and the board.
5. Fix with self-drilling screws.
6, the middle of the width of the sun plate 1.05M must be under the skeleton, is fixed with a self-drilling screw sleeve button.
7. The solar panels on the wall shall not be in direct contact with the wall, and shall be fixed to the wall with angle aluminum, and then the sun panels shall be put in and installed.
8. Seal the mouth of the sun board with aluminum tape, then fix the edge strip or angle aluminum.
9. First check whether the cutting size and expansion reserve of the sheet are suitable. Pay attention to leave enough uniform expansion gap. The calculation formula is as follows: total expansion gap = expansion coefficient * large temperature before and after local installation * Plate length.
10. In the hollow board installation project, the part of the plate clamped by the stencil must contain at least one rib, or the part where the edge of the plate is clamped is 20 mm smaller. Identify the UV-resistant side of the sheet and install it face-out. Never allow the UV-proof side to be installed inward.
Sunshine board canopy installation notes:
1. Check whether the cutting size and swelling reserve of the sheet are suitable. Pay special attention to leave enough uniform expansion gap. The calculation formula is as follows: Total expansion gap = expansion coefficient * Maximum before and after local ampoules Temperature * sheet length.
2. In the hollow board installation project, the part clamped by the stencil must contain at least one rib, or the part where the edge of the sheet is clamped is at least 20 mm.
3. Identify the side of the surface of the sheet that is protected from UV rays, and install the side facing outwards. Do not allow the UV-proof side to be installed inward.
4. Before installation, lift the protective film around the board to 30MM-50MM. Do not let the profile clamp the protective film, but you can't remove too much to avoid damage to the board due to operation.
5. When the self-tapping screws are tightened, the force should be even, to ensure that the stencils actually compact the sealing strips and plates.
6. In the case of cold-formed installation of hollow sheets, the bending radius shall not be less than 175 times the thickness of the substrate.
7. The hollow sheet can only be bent in the direction of the ribs.
8. The inclined installation of the hollow sheet should be in the direction of the ribs, which is conducive to the condensed water.
There are many problems to be aware of when installing a light panel canopy, so it is necessary to learn how to install it before installation. The above is the installation method and installation precautions for the sun panel canopy introduced by Xiaobian today. To finish more information, please continue to pay attention to the decoration home.
More related wonderful reading:
How to build a sun awning canopy? Sunlight canopy notes
Sunlight canopy price sun panel canopy features
Sunshine board canopy how to install sun board canopy installation precautions
In order to develop the mortar formulation or Quality control for mortar production, mortar lab is necessary to be established. There are quite some basic equipments or accessories for a standard mortar lab such as mortar mixer with different volume, portable or table-type pull-off tester for tensile adhesion test, flexural & compressive test machine, universal testing machine for elongation test, drying oven or curing chamber for controlled temperature and humidity, seiving machine for sand grading and so on. Except the international standard requiremnt, some special test method can also be fulfilled by some tailor-made facilities, which is also possible to be designed or manufactured here.
Cement mortar mixer, tensile adhesion test, pull-off tester, universal testing machine, curing chamber
Shanghai Na Long Tech Co., Ltd , https://www.na-long.com